Is there currently a way to get the Filter back?

When I try to enable the System Capture it says: Capturing not enabled, please try again! 
I removed the Filter manually, but now I cannot add it back, I won't get asked. I checked if there is some local Storage, but couldn't find any.

I just need to sync the last decent, tolerable version of Evernote one more time: https://www.reddit.com/r/Evernote/comments/1cico6e/solutions_for_syncing_the_legacy_v6_client/

How can I do this?  I can't find a way to change the user-agent globally for running programs under WINE.  It's supposedly possible under FIDDLER but I'm new. :(  Help?  I searched the documentation and program, but I must not be good at this because I couldn't figure it out.

This happens when running Fiddler Everywhere for the first time, I've tried reinstalling it multiple times, running as Administrator and nothing.

 

I'm running on a Windows 11 pro, it's my personal computer there are no network blockers, I can ping the endpoints mentioned in this answer: https://www.telerik.com/forums/unable-to-accept-the-eula-please-try-again-later-if-the-problem-persists-please-contact-support

 

I thought maybe I was imagining this, but I can consistently reproduce it. Problem started with Fiddler Classic, and I then tried Fiddler Everywhere only to see the same behavior:

My dev/debugging environment consists of MS Visual Studio, Postman, and Fiddler running on Windows 10. I always have MS Outlook, MS Teams, and SSMS running as well. I run both Visual Studio, Postman, and Fiddler as Administrator, though I've tried running them in normal mode as part of debugging this problem. It makes no difference.

Any time I start Fiddler, within approximately 15 minutes, Teams is the first app to go down... it suddenly reports "no internet connection" and I can't send or receive messages.

Shortly thereafter, Outlook will start throwing up "invalid security certificate" dialogues. Email send/receive is no longer possible after this point... The Outlook Icon in my taskbar shows a yellow triangle with a black exclamation mark.

Next to go is the ability to make https connections through, for example, Chrome or Edge.  I see errors such as the attached.

Has anyone else experienced this behavior? I've tested extensively making sure just the apps I've mentioned earlier were running. I can run for 24, 48, or more hours without the problem occurring. But if I fire up Fiddler (either Classic or Everywhere), 100% of the time, the networking issues occur. Always.

Any thoughts on what might be going on here? My assumption is that Fiddler is trying to be a proxy for everything on my machine, and it just can't do it for <reasons>. If I remember correctly I can manually tell Fiddler NOT to proxy for certain apps, but this seems tedious. I'm especially worried to suddenly see https disabled for Chrome or Edge, as the Visual Studio applications I'm debugging are APIs that use https...

 

 

I'm getting used to the new fiddler interface and am confused about the icon below. A red dot next to a plug would seem to indicate some type of connection error, but the status code of 101, which I admit I wasn't familiar with until now, doesn't seem to be a failure.

I'm trying to debug an API that uses RabbitMQ and SignalR for async communication. My C# code is throwing a connection error exception right around the time that the above shows up in my fiddler trace. Everything else in the debug session shows up like below:

 

But since 101 isn't a 400 or 500 error like I'd expect, I don't understand if the icon of a plug with a red dot next to it is trying to tell me something went wrong.

 

TIA for any help

So I'm finally trying Everywhere vs. Classic and the first thing I've noticed is there doesn't seem to be any way to set up Everywhere so it doesn't show all the annoying, distracting traffic I don't care about and don't want to see (e.g. callouts by Microsoft Outlook, Teams, Chrome extensions, etc.)

This was a really important option. Surely they didn't take it away? With all the extraneous traffic flowing through, the things I really want to see get lost in the noise.

For my use case, it is NOT helpful to filter for ONLY certain URLs, etc. I just need to filter things OUT.

Please, what am I missing?

[NOT POSSIBLE ANYMORE, DELETE PLEASE]

Gentlemen,
Ladies,

My question is relatively simple. I do all of my work on a Mac Studio M1, using OsX.

When doing .NET development I usually run Visual Studio on Windows 11 on ARM or in another Virtual machine, run from an actual Windows machine.

I'm not a big fan of the 2nd option, since the machine can be sluggish at times, but... the VM has Fiddler Everywhere up & running, the Parallels version does not.

Windows for ARM allows me to install the application, but it does not start up.

I do have Fiddler installed on my Mac itself, so I was wondering... is there a way I can monitor/capture what's occurring on my Parallels machine?

Hey,

currently trying the grpc Feature of Fiddler Everywhere. I have no Protofile (not sure if it is required at all).
But when I running Fiddler as Interceptor (I using Proxifer to reditrect traffic to Fiddler Everywhere)

it tells me: Incomplete Message on the Response.

When I run the App without Fiddler it works, so I assume Fiddler can't handle the grpc yet. Or is the Protofile required for him to handle  + forward the message?

Good day,

 

so im running the trial versions, and it seems like i have to configure every device i want to monitor individually?

cant i point my router to fiddler and through that see all my connected devices?